•  
Welcome, Guest. Please login or register.
Did you miss your activation email?

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - uaf

Pages: [1]
1
Recruitment / UAF Recruitment in Saginaw MI
« on: September 19, 2015, 08:06:48 AM »
Hi, I'm somewhat new to airsoft. Me and my buddies used to play all the time doing backyard plinking. Then I went on YouTube and found some MilSim videos. Ever since then I've been obsessed with airsoft. I ordered myself a whole loadout. I really want to get a team toget her to go to MilSim events and also just play little one on one's against other squads.
I prefer that everybody have a black or urban themes loadout as UAF stands for Urban Assist Force
Looking for players in and around Saginaw that want to get into airsoft.
Ages 14+ are preferred. Exceptions may be made.

2
Tech Questions / Re: M4 Mags in an AK?
« on: August 23, 2015, 10:04:26 AM »
Quote from: Pagan on August 23, 2015, 09:59:49 AM
http://www.evike.com/products/56322/

Here you go.
Thank you!!

3
Tech Questions / M4 Mags in an AK?
« on: August 22, 2015, 08:56:56 PM »
I have a friend who wants to go play airsoft with me but he only has one mag. I was wondering since I have so many M4 mags if there is any adapter to fit an M4 mag in an AK.

4
Tech Questions / Re: ICS PAR MK3 Motor Overheat??
« on: August 22, 2015, 08:27:08 PM »
Quote from: T6e9a on August 22, 2015, 05:50:29 PM
More than likely, your trigger contact may have fried. Either that or something with the motor.

If there is no MOSFET in the gun, it is not 11.1 lipo ready. It may be tuned well, but trigger contacts will always be a weak point.

The slowing down sounds like something may have gone wrong with the motor.

But without having the gun yourself to check things, you'll have to ask the person working on it a to what really happened.

If you did have it, I would say take off the baseplate of your motor grip, unplug the wires, and pull out the motor. Check the brushes, brush springs and the tabs that the connectors go on. If everything looks symmetrical on each side, and nothing broken, plug it in OUT of the grip, and test. If the motor spins, then it may have been a bad connection to the motor. If it doesn't spin, it is probably somewhere else in the wiring harness, or the trigger contacts.
I will ask when I get it back! Thanks I‘ll make sure to invest in a mosfet.

5
Tech Questions / Re: ICS PAR MK3 Motor Overheat??
« on: August 22, 2015, 09:41:17 AM »
Quote from: T6e9a on August 22, 2015, 09:12:11 AM
If you were holding the trigger down for three straight hours, then ANY gun would heat up... Something internally would probably melt as well. Airsoft guns are built for that.

I mean, if you want to know what happened, ask the person repairing it.

Your description of "it then began to slow down and it eventually stopped shooting"  tells me that you ran your battery dead.
More info, such as what battery you were using? Had there been any upgrades? Can all help people help you.

Other possibilities, might be that the shimming and motor height were too far off and that they cause too much friction in the system.
I was not holding it down for 3 straight hours and the battery worked in my friends gun afterwards. Keep in mind it was like 90 degrees. I was using a Valken 11.1v 1100 Mah battery. And my gun is lipo ready and that is the suggested battery for it. So I dont know what happened. I also tried my friends battery in my gun and it didn‘t work.

6
Tech Questions / Re: ICS PAR MK3 Motor Overheat??
« on: August 21, 2015, 08:58:01 PM »
Quote from: T6e9a on August 21, 2015, 08:31:34 PM
How long were you shooting it on full auto? Afterwards, did you test the battery elsewhere to rule out the battery not draining?
Sorry I forgot to quote you on my reply.

7
Tech Questions / Re: ICS PAR MK3 Motor Overheat??
« on: August 21, 2015, 08:56:22 PM »
Probably 3 Hours and yes my battery was working I had put it in my friends gun and it fired fine. And I know its not the connectors as the fire slowed down then stopped.

8
Tech Questions / ICS PAR MK3 Motor Overheat??
« on: August 21, 2015, 08:26:52 PM »
I have a ICS PAR MK3. Now a few weeks ago it was very hot outside and I was outside playing on full auto, it then began to slow down and it eventually stopped shooting, the motor grip was very hot. I have it being repaired right now, yet I would still like to know what happened so I can prevent it from happening again.

Pages: [1]